Stickist.com https://stickist.com/ |
|
railboard active mode cable wiring https://stickist.com/viewtopic.php?f=2&t=12247 |
Page 1 of 2 |
Author: | pretensions [ Sat Jun 03, 2017 7:29 pm ] |
Post subject: | railboard active mode cable wiring |
I had a spot of bother with an R-Block recently that seemed to coincide with my first use of active mode, and now I'm paranoid about trying active mode again. Here's what I observe with a multimeter in the TRS->dual XLR cable setup: * Tip to pin 2 bass * Ring to pin 3 melody * Side to pin 1 both * No other continuities Could someone confirm that these connections are what I should see? Or point me to where I could find this information? I checked the R-Block manual but there's no wiring diagram. Thanks! |
Author: | Gerald [ Tue Jun 06, 2017 9:06 am ] |
Post subject: | Re: railboard active mode cable wiring |
Can anyone help? I have not the original cable TRS->XLR Cable and all adaptors i tried ended in a horrible signal/noise ratio. So... I think this is an important information. Also it seems that there is a difference between european and US cabling in this case - I saw 2 different connections in google... |
Author: | Claire [ Tue Jun 06, 2017 10:10 am ] |
Post subject: | Re: railboard active mode cable wiring |
Since the Railboard uses a custom splitter cable, it would be best to confirm the pinout/wiring of those connections with Stick Enterprises. As far as standard connections... TRS Tip - positive Ring - negative Sleeve - ground XLR Pin 1 - ground Pin 2 - positive Pin 3 - negative (Some equipment manufacturers use a different pinout, and when using XLR for unbalanced connections pin 1 and 3 can also be connected.) |
Author: | Skydiver [ Tue Jun 06, 2017 11:39 am ] |
Post subject: | Re: railboard active mode cable wiring |
Claire, Pin 1 is typically the ground or shield. Pin 3 is typically the negative and is grounded for unbalanced connections. |
Author: | Claire [ Tue Jun 06, 2017 1:00 pm ] |
Post subject: | Re: railboard active mode cable wiring |
Whoops! Yes, thanks Dean. Just corrected my post. As I noted - best to check with SE for specifics. |
Author: | Skydiver [ Tue Jun 06, 2017 2:30 pm ] |
Post subject: | Re: railboard active mode cable wiring |
I used to be a studio technician in a previous life... AKA Solder Monkey... |
Author: | pretensions [ Tue Jun 06, 2017 3:14 pm ] |
Post subject: | Re: railboard active mode cable wiring |
Thanks for the replies. Claire, your general info is at least consistent with what I observe, and I agree SE is my next stop. |
Author: | Claire [ Tue Jun 06, 2017 3:19 pm ] |
Post subject: | Re: railboard active mode cable wiring |
Skydiver wrote: I used to be a studio technician in a previous life... AKA Solder Monkey... pretensions wrote: Thanks for the replies. Claire, your general info is at least consistent with what I observe, but I agree SE is my next stop. |
Author: | pretensions [ Mon Jul 03, 2017 12:15 pm ] |
Post subject: | Re: railboard active mode cable wiring |
Update of little substance: I've emailed SE a few times about this question but I haven't heard anything back yet. I'll give them another week to reply to my latest request, and then I'll take the plunge and try active mode anyway. To satisfy an extra measure of paranoia, I measured the phantom power in my input XLRs and everything is fine--not a surprise, as these channels have been driving mics for years. |
Author: | Gerald [ Tue Jul 04, 2017 12:32 am ] |
Post subject: | Re: railboard active mode cable wiring |
pretensions wrote: Update of little substance: I've emailed SE a few times about this question but I haven't heard anything back yet. Interesting - some guys reported this problem - I always got a reaction in 24 hours (workdays)... Probably a Spamfilter-thing? |
Page 1 of 2 | All times are UTC - 8 hours [ DST ] |
Powered by phpBB © 2000, 2002, 2005, 2007 phpBB Group http://www.phpbb.com/ |